ENGINEERING REFERENCE / SHEET 02
From a weak restart to a field decision.
Screen a candidate well, see where each product might fit, and prepare the evidence for an engineering review. Browse 31 engineering questions below.
-
BEFORE SHUT-IN
Record the last stable oil rate, pressure and lift load.
-
AFTER RESTART
Compare the same readings and note any setting changes.
-
BEFORE A FIELD DECISION
Look for deposit evidence and rule out other causes. A weak restart alone is not a diagnosis.
01 / Start at the well
Is there a recoverable constraint?
Example: A progressing cavity pump restarts after a shut-in. Oil rate is below its previous baseline and the drive needs more torque. Deposits are one possible cause, but a change in fluid viscosity, pump wear, stator fit or drive conditions could produce similar signs. Start with evidence, not a product.
Establish the baseline.
Compare stabilized oil and total-fluid rates, pressure and lift measurements before and after restart. Note changes in settings, water cut, gas behavior or recent work.
Locate and characterize the issue.
Separate possible inflow restriction, tubular deposits and equipment drag. Use available fluid characterization, deposit samples and inspection records; a rate or load change alone cannot identify the material or the location.
Check other explanations first.
Review mechanical integrity, lift condition, reservoir decline and water production. If the actual constraint is unknown, gather more evidence before proceeding.
Make any field evaluation measurable.
Agree on a primary metric, comparable conditions, a monitoring window and stop criteria. An operator-approved, well-specific plan is required before field activity.
02 / Product roles
Treating deposits is not the same as reducing drag.
- SolidsFree 432
- American Well Technology describes this as a deposit-focused treatment and surface preparation. Its materials discuss mobilizing wax or asphaltenes and preparing surfaces for a possible ongoing program. That description does not establish organic damage or contact with the affected interval in any given well.
- ALS Production Lubricant
- AWT describes this family as surface-active chemistry intended to change the metal or flow-path interface and reduce friction or drag. It publishes separate references for ESP, PCP, reciprocating rod lift and gas lift. The manufacturer descriptions do not establish quantified effects, compatibility or clearance for use.
| Lift system | Useful signal | Another cause to check |
|---|---|---|
| ESP | Motor load, pressure, throughput | Gas interference, intake conditions, wear |
| PCP | Drive torque, speed, throughput | Fluid viscosity, solids, stator fit |
| Rod lift | Rod loads, fillage, stroke settings | Pump condition, tubing wear, alignment |
| Gas lift | Injection conditions, pressure, rate | Gas supply, valve or choke behavior |
Comparison points are review prompts, not diagnostic thresholds. Product descriptions are attributed to the manufacturer, not independent field findings.
Product source: American Well Technology chemical and lubricant overview. The manufacturer describes intended uses; this is not independent field evidence.
Lift system drawings
Four systems, four places to look.
See how each system moves produced fluid and where a suspected deposit or drag problem is worth investigating. These conceptual drawings are not to scale. Teal arrows trace produced fluid; dashed copper traces injection gas.
SolidsFree 432 is intended to mobilize organic deposits where the treatment reaches them.
ALS Production Lubricant is intended to reduce drag at the equipment or flow-path interface it contacts.
Reciprocating rod lift
The rod drives the plunger. On the upstroke, the plunger lifts produced fluid toward the surface.
Check for deposits in the tubing separately from drag where the rod string contacts it. Compare rod loads and pump fillage at similar stroke settings.
Electric submersible pump
A downhole motor turns a stack of impellers. Fluid enters at the intake and moves up through the stages into the tubing.
Check the intake and tubing for deposits. Evaluate lubricant contact with wetted metal separately; compare motor load, pressure and rate at similar drive settings.
Progressing cavity pump
A helical rotor turns inside a fixed stator. Moving cavities carry fluid up toward the tubing.
Check for deposits in the flow path. Compare torque, speed and output, and verify stator material compatibility before considering a lubricant.
Continuous gas lift
Injection gas travels down the annulus and through a valve into the tubing. The lighter gas–liquid mixture rises. There is no downhole pump.
Check gas supply and valve behavior first. Compare injection, tubing pressure and production; evaluate any deposit or flow-path drag issue separately.
The highlighted areas show possible contact zones, not an injection route, compatibility approval or a predicted result. Component arrangements vary by completion.
Equipment references, SLB Oilfield Review: rod pumps, ESP, PCP and gas lift. These explain the equipment, not the treatment’s performance.
03 / Engineer handoff
What to send with a candidate.
Send an approved candidate summary through your own secure review process. Start with what is available and mark missing data; this page does not receive or transmit well data.
- Asset and lift: completion, equipment, materials and known integrity limits.
- Timeline and baseline: shut-in dates, restart response, settings, interventions, and comparable production and pressure trends.
- Fluids and solids: crude characterization, deposit observations, water cut and gas-to-oil ratio where available.
- Decision and uncertainty: suspected constraint, competing explanations, what is unknown, and what would justify a controlled evaluation.
Initial commercial contacts
Start with a brief overview. Ask for a secure transfer route before sending confidential well files.
The operator and engineer must review materials, current safety documentation, handling and disposal requirements, and operating limits before authorizing a field plan. No site-level instructions are provided here.
Complete reference
31 questions behind a field trial.
Jump to a topic, then open any question for its answer.
Area 01
Executive case
Decide whether there is a specific, testable production problem.
What production problem is this approach meant to address?
It is a way to evaluate a possibly recoverable constraint from organic deposits, resistance to inflow near the well, or friction in the lift system. It is not an explanation for every declining well.
Why can a well restart below its earlier production rate?
A shut-in changes temperature and pressure. Depending on the crude, wax or asphaltenes may become unstable and build up in the production system. Compare the restart with a credible earlier baseline and look for supporting deposit evidence.
Does a weaker restart always mean the reservoir is depleted?
No. Separate a possible new restriction from reservoir decline, water breakthrough and mechanical or integrity problems. The timing of the change is a clue, not proof.
Why investigate chemistry before committing to a workover?
When evidence points to an organic restriction, compare a targeted chemical evaluation with the mechanical alternative. If equipment or completion integrity has failed, a chemical treatment is not a substitute for repair.
Why screen a portfolio instead of buying treatment for one well?
Screen to find a repeatable candidate pattern. An observed result helps decide whether to evaluate other wells with similar fluids and operating conditions; it does not transfer automatically.
Area 02
Shut-in damage
Understand the mechanisms, then check whether they fit the well.
What is wax appearance temperature?
Wax appearance temperature is the crude-specific temperature at which wax crystals begin to appear under the test conditions. Cooling below it can raise deposition risk, but does not show where or how much wax accumulated.
How can a shut-in affect asphaltene stability?
Changes in pressure, gas behavior or fluid composition can affect whether asphaltenes stay dispersed. Confirm the fluid behavior for the actual crude rather than assuming the response.
What does compounded skin mean?
Skin describes added resistance to flow near the well. A pre-existing restriction from one cause can coexist with new damage from another; the pressure or rate response alone does not identify either cause.
Why review low gas-to-oil ratio in mature wells?
The ratio helps describe fluid and lift behavior and can matter when comparing restart conditions. Treat it as context alongside fluid tests, pressure, temperature and deposit history, not a standalone predictor.
Can flow alone clear the damage at restart?
Moving fluid may carry loose material, but adhered deposits or a restricted inflow path can persist. Avoid treating a higher restart rate or drawdown as a diagnosis or remedy.
Area 03
Treatment chemistry
Separate the manufacturer’s intended uses from proof of performance.
What is SolidsFree 432 STIM intended to do?
AWT positions SolidsFree 432 as a deposit-treatment option for suspected wax and asphaltenes. The actual location, nature and extent of a restriction still need evidence; surface observations do not prove near-wellbore effects.
How is dissolving wax different from dispersing asphaltenes?
The distinction is between making crystalline wax mobile and breaking up or keeping asphaltene material dispersed. Identify the deposit first rather than assuming a response to one mechanism predicts the other.
How does ALS Production Lubricant differ from a deposit treatment?
AWT describes SolidsFree 432 as deposit-focused and its lift-specific lubricants as intended to address friction and drag at equipment and flow-path interfaces. These are different roles, not evidence of treatment performance in a particular well.
Which lift systems can be evaluated?
AWT publishes separate application references for electric submersible pumps, progressing cavity pumps, reciprocating rod lift and gas lift. Select the reference by actual equipment and confirm materials, fluids and operating limits independently.
Does the chemistry replace corrosion, scale or mechanical programs?
No. Inorganic scale, corrosion, sand, incompatible fluids and equipment or integrity failures can require distinct responses. Retain the existing safeguards until the operator approves any change.
Area 04
Candidate screening
Bring comparable records and identify reasons not to proceed.
What makes a strong candidate?
Start with a credible production shortfall and evidence that points to physically plausible deposit or lift drag, after reviewing competing causes. Crude color or downtime by itself is not enough.
How long must a well be shut in?
There is no qualifying duration on its own. Capture how long the well was offline, the fluid and temperature history, the restart response and any recurring deposit evidence.
What records should we review first?
Bring pre-shut-in and restart production and pressure, fluid or PVT data if available, water cut, gas-to-oil ratio, previous treatments or interventions, and relevant integrity evidence.
Which lift measurements are useful?
Use indicators tied to the system: ESP current or load, PCP drive torque, rod loads and fillage, or gas-lift injection and pressure. Record operating settings and changes so the comparison is interpretable.
What should disqualify or pause a candidate?
Pause on integrity issues, confirmed mechanical failure, an unaddressed dominant reservoir or water-production problem, material incompatibility, or inadequate evidence of the proposed restriction.
Area 05
Field execution
Know what requires a well-specific, approved plan.
What should the field plan cover?
Define the objective, baseline, compatibility and safety review, operator sign-off, restart responsibilities, and monitoring. This checklist is not a treatment procedure.
How is treatment volume determined?
A qualified engineer determines it for the specific completion, intended contact region, fluids and operator limits. Do not copy a number from another well or from a sales reference.
How long should contact or soak last?
Only the approved well-specific plan can set it. Placement, crude behavior, temperature and operating constraints matter. This guide does not prescribe a duration.
Why plan a controlled restart?
Agree on how restart will be managed, how produced material will be handled, and which stop limits apply. Document differences in operating conditions before attributing the response to treatment.
What should be monitored afterward?
Track stabilized oil and total fluid, pressure, water cut and applicable lift measures against the baseline. Capture interventions, setting changes and the duration of any response.
Area 06
Economics and proof
Demand comparable evidence before extrapolating across wells.
What field evidence supports an evaluation?
The original commercial material cites supplier-reported analogue experience. Treat those reports as leads for diligence, not verified local outcomes; request source records, conditions, timing and a comparable baseline.
Can U.S. and Venezuelan experience inform a Gulf field trial?
Similar crude or deposit behavior can suggest what to investigate. It cannot show regional performance without checking local fluids, reservoir, lift system and operating conditions.
What outcomes should a field evaluation measure?
Agree on a production or lift indicator tied to the original problem, a comparable baseline, the observation window and how you will record competing changes and response durability.
How should the economic case be framed?
Test the value of incremental production and any documented downtime or intervention avoided against treatment, operations and monitoring cost. Use local assumptions and show which ones drive the result.
Does a worked economic example predict this well’s result?
No. An illustrative scenario shows how input assumptions affect the economics. Replace them with site data and check downside cases before relying on the model.
What is the first commercial step?
Prepare one plausible candidate and agree with the operator on the problem, measures, engineering gates and what evidence would justify another trial. Do not commit to broader use on the basis of a screening outcome.
